Видео

Great video do some more ur great at it. I need front shocks can u do a video on that😊

Does anyone know how to get the valve to seal when applying negative pressure ?

the performance analysis parts (Murphy) friction fit inserts for the large double connector pods are junk. The travel is very limited and they never worked no matter how hard I tried on my 85 300sd. Just get a good junkyard one or buy new and save yourself wasted money and aggravation.

I think that little black sensor is the buzzer switch but I'm not 100% sure. It's annoying and that's probably why it was unplugged.

nice job mjm. Eho did you order parts from? Cost? My 85 slips if I give it to much gas starting but doesn't slip if I baby it. Do you think putting in a new piston would fix that?

IT seems to me dropping the tranny would make it easier? I have dropped two in my life and they come out reasonably easy with extensions and wobble sockets leaving the engine in. Why do you say you need to pull the engine with the tranny?I have not heard that so I just pulled the tranny. I also have a slipping first gear and it even makes a noise when it slips but it has done this for many years and if I dont try to make a fast start it doesn't slip. do you think the B2 piston in mine needs replacement?

I thought this video would show how to adjust the toe in which I need to know - congratulations on getting your toe in perfect - thanks for sharing

Why you didn’t vacuum that box inside before install new filter? That’s not smart in my opinion

thanks for sharing i recenlty upgraded to all LED style bulbs and now I have HYPER FLASHER I dont wannaget pulled over. i ordered on of these relays on ebay. It suck I have to take apart the whole dash ! ugh

thank you. I have a rattling under my shifter on my 85. will get to it!!

do you have a part number for that sensor?

This was really helpful, Thanks! SUBSCRIBED!!!

Best video for doing valve cover gaskets yourself. So helpful! Thank you!

that car is so good i love it

Awesome video I have both ports leaking

anyone knows what battery is used? i need to get a replacement

10:33

8:49

My car is vibrating then running nice then vibrating again at minutes apart and vibrating for few seconds at a time. How was yoir vibration? Im trying to troubleshoot mine

Hey nice video! Couple questions tho, would it be better to clean off built up oil on the valve cover after you take off ignition coil bracket? Also can you do this job without using trans assembly, what if you have nothing, just the gasket, would that be ok?

Thank you for that video, he helped me a lot, fixed my problem AC and tach working now

You are right! What a mess. I had to rebuild my 350 and after having some trouble trying to get the engine to turn, I decided to find a demonstration about re-installing the rod caps. Thanks for the information. I bought my truck for a guy and 18 mons. earlier if was bought from a car dealer. Best guess the character at the car dealer rebuilt the engine. trying to make a buck, right? probably didn't match up everything as he should have done. He was in a hurry!

Hi,is that a quick struts..thank you

thank you for the video i am having the same issue took it to a machine shop and guy told me caps are all mixed up

Where to buy these wheels?

This video made my job easy. The extra tps you throw in make it easier for sure. Thanks dude

My question is ...the hoes adapters that conect to the low side and the hight side are they the same or do they change co.pared to the modern ones?

Looks good.

1st view

If you take the wipers and top trim piece off, you don’t have to remove the intake or anything

Good tips! Thanks

I have a 4.3 V6 2000 gmc sierra , will this work?

Worked great Thanks!

Can't see! Your hand is in the way. 🤦🏽‍♂️

شكرأ من سوريا حلب اعمل في نظام سسبنشل سيرفيس بمرسيدس 34 سنه لماذا لم تغير جزء اخطر يوجد سيال تفرون ابيض صغار 2 داخل حلازون نصف

A very well put together and helpful video. The information on the shim was gold. Thank you 🙏

ouch- low volume on voice- high on music..... like the content tho.

How much more lift can I get by running the Comp cams 26918 springs and Comp cams 787-16 retainers? I have stock Vortec heads with a Comp Cams CL-262-4 Cam with 0.464/0.470 lift. What clearance can I get with out needing to machine the valve seats?

Wrong drain plug Dude, check your manual. The right drain plug is a lot easier to get to and it's metal!

DIDNT FIX IT ON MY 2011 Sienna 3.5L Still blinking light clutch doesn’t engage

🙏 thank you for your help

If the connector cant squeeze in to remove the old fuel filter.. grab a small hacksaw and cut the fuel filter off at the nipple/connector.. now with the fuel filter out of the way, those little tools will fit around the nipple and easily pop it out!! 👍💯

Great video! Mair difference!

This is a terrible video. Showed nothhing

you did not do your homework on the Equinox. 1. you can cancel the auto stop start problem by putting the gear shift in low and use the plus on top of the shifter to go through the six gears & leave it at 6th gear you can see the gear changes on the dashboard. you need to do this every time you start the car, put in low and use the plus on top of the knob take it up to 6th gear. THE CAR WILL SHIFT NORMALLY ONCE YOU SEE THE NUMBER 6 2. You need to use the info. screen to add more displays. I found it and added battery volts, coolant temp & oil pressure. City driving with pot holes it can be a little rough. She handles really well on the highways. My Equinox is a little over four years old now. mileage is 71,000. My service guys at the dealership say I take really good care of the Equinox. I have heated seats, wish I would have ordered the heated steering wheel. Living in the northeast can be pretty cold

If you don't mind could you give a link to the bushing tool you used on an upper arm?

8:50- The washer that goes over that tensioner pulley mounting bolt is not flat. Wish you'd of covered that in a bit more detail. My guess is that the indented side of that washer should be installed with the indented side AWAY from the bolt head. Do you agree? Thank you.

I really appreciate your videos, I wish there was a video of these vacuum "solenoids" getting bench tested so I can see what you're doing with maybe an external power supply energizing them.

Curious, what happens if you put a magnet on the sensor and don’t take it off all summer? Then when it gets cold out, remover the magnet and the heat works fine. Thoughts?

Happen on 2013 Highlander after 10 yrs it gone bad (but also after sitting a lot during Covid) going to try small magnets on top of the original (hopefully no need to epoxy too